DK2 Rampage II RAMP8219 Custom-Mount Winch Snow Plow

The DK2 Rampage II (RAMP8219) is an 82 x 19 in. personal snow plow for light trucks and SUVs, built to clear driveways, lanes and small parking lots. It slides onto a vehicle-specific custom mount, sold separately, and a 3,000 lb electric winch raises and lowers the blade from inside the cab with the included wireless remote.

One lever locks the blade straight, left or right, and trip springs let it tip forward over buried obstacles, then pull it back. To take the plow off, disconnect the wiring, remove the two locking plates and roll it away on its flip-down castor wheels.

Construction is 14-gauge steel with a UV powder coating, built by an ISO 9001 certified manufacturer and covered by a 1-year limited warranty. Marlon rates the plow for light personal use; it is not intended for commercial plowing.

• Custom vehicle mount: the plow slides onto vehicle-specific brackets and locks in with two quick-mount locking plates. Fits most light trucks and SUVs.
• 3,000 lb wireless electric winch: lifts and lowers the blade from inside the vehicle with the included wireless remote.
• Three locking blade angles: a single lever sets the blade straight, left or right.
• Trip springs: absorb shock on uneven surfaces and let the blade trip over hidden obstacles.
• Flip-down castor wheels: carry the plow while you mount and remove it, then roll it away for storage.
• Rubber snow deflector: cuts down the snow thrown over the blade onto the windshield.
• Hardened steel scraper with skid shoes that hold it at a set height.
• Polymer-wrapped wire rope plow markers show the blade's outside corners in blowing snow.

The Rampage II needs a vehicle-specific custom mount kit, sold separately. The mount is a pair of brackets made for your vehicle, joined by a cross member. The cross member ships with the plow, and the bracket kit includes its own installation instructions.

Find your kit number in the Custom Mount Kit Guide under Documents. It lists kits by make, model, year and 2WD or 4WD. Kits marked with an asterisk also require the extended cross bar, and some vehicles need a bumper skirt, air dam or tow bar removed before the mount goes on. Marlon states that its SnowBear by Marlon mount kits fit DK2 by Marlon plows.

With the plow on, the vehicle must stay within its gross vehicle and front axle weight ratings (GVWR and GAWR) on the driver's door pillar. Rear ballast, such as sand bags behind the rear axle, may be needed.

• Hardened steel scraper
• Rubber snow deflector
• Polymer-wrapped wire rope plow markers
• Skid shoes
• Castor kit
• 3,000 lb electric winch with wireless remote
• Cross member (vehicle brackets sold separately)

Ships in a single carton on a standard-size pallet.

Marlon covers this plow with a 1-year limited warranty to the original purchaser against manufacturing defects in workmanship and materials under normal use. Within that year, Marlon replaces or supplies any defective part at its option. The warranty does not cover disposable parts such as scraper blades, plow springs, plow markers, snow deflectors, winch straps and hardware, or labor, installation and shipping charges. The owner's manual adds that the plow is intended for personal use only and that commercial use voids warranty claims.

Is the cross member included?

Yes. The parts list in the owner's manual includes one cross member, which joins the two vehicle brackets. The vehicle-specific bracket kit is sold separately, and kits marked with an asterisk in the mount guide require the extended cross bar.

How do the mount brackets go on?

DK2 says to fit both brackets loosely, loosely fit the cross member between them, then tighten the brackets and finally the cross member. If they do not line up, check the kit number in the mount guide.

How is the winch wired?

A 35 amp circuit breaker goes on the red wire between the winch control box and the battery. It protects the winch and the vehicle's electrical system.

How high should the skid shoes be set?

DK2 recommends about 1/4 in. below the scraper blade. The skid shoes protect the surface you are plowing and reduce wear on the scraper.

How fast can I plow?

The owner's manual says not to plow above 10 mph (15 km/h). Faster speeds can overload the plow and cut cooling air to the engine.

Do I need plow lights?

The owner's manual recommends plow lights for plowing at night, because the blade will likely block the vehicle's headlights. DK2 sells plow light kits separately, including the LK4200LB2 LED kit and the 81488LB2 halogen kit.

What is the difference between the Rampage II and the Rampage II ELITE?

The Rampage II ELITE (RAMP8219ELT) mounts the same way but lifts the blade with a 3,000 lb IP67-rated, fully sealed electric actuator instead of a winch.

• Custom Mount Kit Guide (PDF)
• Rampage II, Storm II and Summit II Owner's Manual (PDF)