Auxx-One Motorized Overhead Garage Storage Lift, 400 lb Capacity, Wireless Remote

The Auxx-One is a single-motor overhead lift that turns unused ceiling space into organized storage. It raises and lowers heavy, awkward gear on a galvanized-steel lifting frame at the press of a wireless remote, with a 400 lb lifting capacity that covers most of what ends up cluttering a garage floor.

A tubular motor mounted to your ceiling winds two vinyl-coated aircraft cables that carry the load on a 5 ft snap-in E-Beam. The cables are spaced apart so suspended items rise level and don't spin or twist. Programmable stop points let you set the exact high and low limits for your ceiling, so the load stops where you want it every time instead of drifting into the rafters or down onto the floor.

What you can store overhead:

• Mountain, cargo, and electric bikes — and even motorcycles
• Canoes, kayaks, paddle boards, and small boats
• Truck caps, camper shells, and pickup toppers
• Jeep soft tops and hard tops
• Rooftop tents
• Fifth-wheel hitches
• Bulky, hard-to-store gear — cargo boxes, wheelbarrows, tool boxes, and workbenches

The Auxx-One runs on a standard 120V household outlet and installs as a DIY project, mounting to your ceiling framing with the included strut channels and lag bolts. Because it anchors into structural framing overhead, plan the mount around your joists or trusses — the included installation guide walks through the layout.

Clear the floor without the heavy lifting

Bulky items move up and out of the way instead of leaning against a wall or taking up a parking bay. You skip the overhead reach-and-grab that makes storing a truck cap or rooftop tent a two- or four-person job — one person can raise or lower a load from the ground with the remote.

Wireless remote with programmable limits

A 433.92 MHz remote raises and lowers the load. Set the upper and lower stop points once and the lift returns to them automatically, keeping items clear of the ceiling and the floor.

Dual-cable safety

Two 3/16 in vinyl-coated 7x19 steel cables — rated to a 4,200 lb ultimate tensile strength — carry the load on widely spaced pick points so it stays balanced and level. The motor also prevents lifting above the rated capacity.

Snap-In E-Beam accessory system

The 5 ft galvanized E-Beam accepts snap-in carabiners, round rings, webbing guides, and J-hooks that add, remove, or reposition in seconds — so you can place pick points exactly where the load balances. The frame is galvanized steel for corrosion and scratch resistance.

• Single-motor lift unit
• Controller
• Wireless remote control
• (2) C-strut ceiling channels
• 5 ft galvanized E-Beam lifting frame
• Mounting hardware (SPAX lag bolts)

Auxx-Lift covers the Auxx-One with a 2-year warranty against defects in materials and workmanship under normal residential use, per the owner's manual. The warranty applies to personal household use and does not cover commercial installations, improper installation, modification, or damage from misuse — it is built and warranted as a home-garage storage system rather than a commercial-shop tool. Proof of purchase from an authorized dealer is required for warranty service.

What kind of power does it need?

A standard 120V household outlet on a 15-amp circuit. The unit ships with a 10 ft, 16-gauge cord and a standard NEMA 5-15 plug, so no special wiring is required.

How high can it lift, and will it fit my ceiling?

The standard configuration provides 12 ft of vertical travel and lifts at roughly 30 seconds per 9 ft of ceiling height. Optional longer cables are available for taller ceilings.

Can I install it myself?

Yes. The Auxx-One is designed for DIY installation and mounts to your ceiling framing with the two included strut channels and lag bolts. Anchor it into structural joists or trusses and follow the included installation guide for layout and spacing.

Will it work with my rooftop tent, truck cap, or Jeep top?

The Auxx-One is used with major brands of rooftop tents (such as Thule, Yakima, and iKamper), truck caps (such as LEER and Ranch), and Jeep tops (such as Bestop and Smittybilt). The snap-in straps and hooks let you balance the load for the shape you are lifting.

Can I run it continuously?

Run the motor up to 3 minutes at a time at full load, then allow about 15 minutes to cool. The motor switches off automatically to protect itself if it runs longer.

Auxx-One Installation Guide (PDF)