{"product_id":"stratus-sae-f10p-10-000-lbs-floor-plate-two-post-lift","title":"Stratus SAE-F10P 10,000 Lbs Floor Plate Two-Post Car Lift","description":"\u003ch2\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eStratus SAE-F10P\u003c\/strong\u003e is a \u003cstrong\u003e10,000-lb two-post car lift\u003c\/strong\u003e built on a floor-plate (baseplate) design: instead of an overhead crossbar tying the columns together, a low-profile plate runs across the floor between them. That leaves the top completely open, so vehicle height is never limited by an overhead beam — useful in low-ceiling garages and when raising taller SUVs, vans, and trucks within the 10,000-lb rating.\u003c\/p\u003e\n\n\u003cp\u003eEach column carries telescoping lifting arms — front arms reach from \u003cstrong\u003e34 5\/8\" to 56 11\/16\"\u003c\/strong\u003e and rear arms from \u003cstrong\u003e26 3\/4\" to 48 7\/16\"\u003c\/strong\u003e — so you can set the contact points to the manufacturer's lift pads on everything from a compact sedan to a full-size pickup. Drive-thru clearance between the arms is \u003cstrong\u003e101 5\/16\"\u003c\/strong\u003e, and maximum lifting height is \u003cstrong\u003e81 7\/8\"\u003c\/strong\u003e with the screw-up adapter pads extended. Eight stackable truck adapters in two heights (2 3\/4\" and 4\") add reach for trucks and SUVs that sit higher off the ground.\u003c\/p\u003e\n\n\u003cp\u003ePower comes from a \u003cstrong\u003e3 HP, 220V single-phase\u003c\/strong\u003e hydraulic power unit that takes the lift to full height in about 50 seconds. A single-point manual release drops the mechanical safety locks on both columns together, and chain-drive columns with equalizer cables keep the two carriages traveling in sync. A top limiter switch stops the carriage at the top of travel, and you can fine-tune lift and lowering speed at the hydraulic oil-flow valve.\u003c\/p\u003e\n\n\u003cfigure\u003e\n  \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0771\/5550\/0318\/files\/stratus-sae-f10p-10-000-lbs-floor-plate-two-post-lift-power-unit-1.jpg?v=1780818567\" alt=\"Column-mounted hydraulic power unit with electric motor, control box, fluid reservoir, and manual release lever\"\u003e\n  \u003cfigcaption\u003eColumn-mounted power unit with the single-point manual release lever.\u003c\/figcaption\u003e\n\u003c\/figure\u003e\n\n\u003cp\u003eThe SAE-F10P is \u003cstrong\u003eCE certified\u003c\/strong\u003e and proof-tested to \u003cstrong\u003e1.15 times rated capacity under dynamic load and 1.5 times under static load\u003c\/strong\u003e. Columns are finished in Granite Gray (RAL 7026) powder coat with Reinorange (RAL 2004) arms.\u003c\/p\u003e\n\n\u003cp\u003ePlan the install before the lift arrives. The columns anchor into \u003cstrong\u003e6 inches minimum of 3,000 PSI concrete\u003c\/strong\u003e (Stratus recommends 6–12 inches of reinforced concrete cured at least 28 days) using the 16 included 3\/4\" x 6\" anchor bolts. The power unit needs \u003cstrong\u003e220V single-phase service on a 30A breaker\u003c\/strong\u003e; the lift ships without a plug, so a certified electrician supplies a 220V–250V 30A plug and makes the connection.\u003c\/p\u003e\n\n\u003cp\u003eThis lift ships by freight. Delivery is to a commercial address, a local installer, or a freight terminal; residential delivery and some remote areas may add carrier fees, and you are responsible for unloading at delivery, where freight carriers allow only a limited window before detention charges apply. To schedule delivery or confirm any surcharges for your area, contact MGS at \u003ca href=\"mailto:sales@mygaragesupplies.com\"\u003esales@mygaragesupplies.com\u003c\/a\u003e or \u003ca href=\"tel:+13073811810\"\u003e307-381-1810\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eFloor-plate base with an open top — no overhead crossbar to limit vehicle height\u003c\/li\u003e\n  \u003cli\u003eChain-drive columns with equalizer cables for synchronized carriage travel\u003c\/li\u003e\n  \u003cli\u003eSingle-point manual release for the mechanical safety locks\u003c\/li\u003e\n  \u003cli\u003eSpring-loaded arm locks hold the lifting arms in position under load\u003c\/li\u003e\n  \u003cli\u003eTop limiter switch stops the carriage at the top of travel\u003c\/li\u003e\n  \u003cli\u003e3 HP, 220V single-phase hydraulic power unit; full rise in about 50 seconds\u003c\/li\u003e\n  \u003cli\u003eTelescoping front and rear arms with screw-up rubber contact pads\u003c\/li\u003e\n  \u003cli\u003eEight stackable truck adapters in two heights (2 3\/4\" and 4\")\u003c\/li\u003e\n  \u003cli\u003eAdjustable lift and lowering speed at the hydraulic oil-flow valve\u003c\/li\u003e\n  \u003cli\u003eCE certified; proof-tested to 1.15x rated capacity (dynamic) and 1.5x (static)\u003c\/li\u003e\n  \u003cli\u003ePowder-coat finish: Granite Gray (RAL 7026) columns with Reinorange (RAL 2004) arms\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eFour screw-up rubber adapter pads (Peg 50 mm \/ 4\")\u003c\/li\u003e\n  \u003cli\u003eEight truck adapters — four 2 3\/4\" and four 4\", stackable\u003c\/li\u003e\n  \u003cli\u003eSixteen anchor bolts (3\/4\" diameter x 6\" long)\u003c\/li\u003e\n  \u003cli\u003eInstallation, operation, and maintenance manual\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eOptional accessories sold separately: cradle pads (Peg 50 mm) and a tripod jack stand.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\u003cth colspan=\"2\"\u003eStratus SAE-F10P Specifications\u003c\/th\u003e\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eLifting capacity\u003c\/td\u003e\n\u003ctd\u003e10,000 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eMaximum lifting height (with adapters)\u003c\/td\u003e\n\u003ctd\u003e81 7\/8\" (2,080 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eMaximum lifting height (without adapters)\u003c\/td\u003e\n\u003ctd\u003e76 3\/4\" (1,950 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eMinimum pad height (with adapters)\u003c\/td\u003e\n\u003ctd\u003e5 1\/8\" (130 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eMinimum pad height (without adapters)\u003c\/td\u003e\n\u003ctd\u003e3 3\/4\" (95 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eRise time\u003c\/td\u003e\n\u003ctd\u003e~50 seconds\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eOverall height\u003c\/td\u003e\n\u003ctd\u003e111 1\/4\" (2,826 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eOverall width\u003c\/td\u003e\n\u003ctd\u003e19 11\/16\" (500 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eOverall length\u003c\/td\u003e\n\u003ctd\u003e134 1\/4\" (3,410 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eWidth between columns\u003c\/td\u003e\n\u003ctd\u003e112 3\/16\" (2,850 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eDrive-thru clearance\u003c\/td\u003e\n\u003ctd\u003e101 5\/16\" (2,574 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eFront arm reach\u003c\/td\u003e\n\u003ctd\u003e34 5\/8\" – 56 11\/16\" (880 – 1,440 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eRear arm reach\u003c\/td\u003e\n\u003ctd\u003e26 3\/4\" – 48 7\/16\" (680 – 1,230 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eMotor\u003c\/td\u003e\n\u003ctd\u003e3 HP, 220V, 60 Hz, single-phase\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eRecommended circuit\u003c\/td\u003e\n\u003ctd\u003e30A breaker\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eHydraulic oil\u003c\/td\u003e\n\u003ctd\u003eAW32 or AW46\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eConcrete requirement\u003c\/td\u003e\n\u003ctd\u003e6\" minimum, 3,000 PSI\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eAnchor bolts\u003c\/td\u003e\n\u003ctd\u003e16 included (3\/4\" x 6\")\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eFinish\u003c\/td\u003e\n\u003ctd\u003ePowder coat — Granite Gray (RAL 7026) \/ Reinorange (RAL 2004)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eCertification\u003c\/td\u003e\n\u003ctd\u003eCE certified\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eShipping weight\u003c\/td\u003e\n\u003ctd\u003e1,385 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eShipping dimensions\u003c\/td\u003e\n\u003ctd\u003e116\" L x 25\" W x 35\" H\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\u003ctd colspan=\"2\"\u003e\u003cem\u003eColumn and drive-thru dimensions are illustrated in the dimension diagram in the product gallery.\u003c\/em\u003e\u003c\/td\u003e\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eWarranty\u003c\/h2\u003e\n\u003cp\u003eStratus covers the SAE-F10P with a \u003cstrong\u003e5-year warranty on the lifting structure\u003c\/strong\u003e, a \u003cstrong\u003e3-year warranty on hydraulic components\u003c\/strong\u003e, and a \u003cstrong\u003e2-year warranty on electrical parts\u003c\/strong\u003e.\u003c\/p\u003e\n\n\u003ch2\u003eFAQ\u003c\/h2\u003e\n\u003ch3\u003eWhat concrete does the SAE-F10P need?\u003c\/h3\u003e\n\u003cp\u003eA minimum of 6 inches of 3,000 PSI concrete. Stratus recommends 6–12 inches of reinforced concrete that has cured for at least 28 days before the columns are anchored.\u003c\/p\u003e\n\u003ch3\u003eDoes it come with anchor bolts?\u003c\/h3\u003e\n\u003cp\u003eYes. Sixteen anchor bolts are included — 3\/4\" in diameter and 6\" long. They are torqued to about 90 ft-lbs (never below 80 or above 110 ft-lbs).\u003c\/p\u003e\n\u003ch3\u003eWhat are the electrical requirements?\u003c\/h3\u003e\n\u003cp\u003eThe power unit runs on 220V single-phase power on a 30A breaker. The lift ships without a plug, so a certified electrician should supply a 220V–250V 30A plug and make the connection. The power cord is 11 feet long.\u003c\/p\u003e\n\u003ch3\u003eCan I adjust how fast the lift raises and lowers?\u003c\/h3\u003e\n\u003cp\u003eYes. The hydraulic oil-flow valve controls speed — tighten it (clockwise) to slow the lift down, or loosen it (counter-clockwise) to speed it up.\u003c\/p\u003e\n\u003ch3\u003eHow do I lower the lift if it is stuck up?\u003c\/h3\u003e\n\u003cp\u003eRelease the mechanical safety locks, then release the pressure in the hydraulic system to bring the carriages down.\u003c\/p\u003e\n\u003ch3\u003eHow long does it take to raise?\u003c\/h3\u003e\n\u003cp\u003eAbout 50 seconds to full height.\u003c\/p\u003e\n\n\u003ch2\u003eDocuments\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0771\/5550\/0318\/files\/stratus-sae-f10p-10-000-lbs-floor-plate-two-post-lift-manual.pdf?v=1780818572\" target=\"_blank\" rel=\"noopener noreferrer\" aria-label=\"Stratus SAE-F10P installation, operation, and maintenance manual, PDF, opens in new tab\"\u003eSAE-F10P Installation \u0026amp; Operation Manual (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Stratus Auto Equipment","offers":[{"title":"Default Title","offer_id":51933886611742,"sku":"SAE-F10P","price":4138.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0771\/5550\/0318\/files\/stratus-sae-f10p-10-000-lbs-floor-plate-two-post-lift-hero.jpg?v=1780820241","url":"https:\/\/mygaragesupplies.com\/products\/stratus-sae-f10p-10-000-lbs-floor-plate-two-post-lift","provider":"My Garage Supplies","version":"1.0","type":"link"}