{"product_id":"stratus-sae-c10p-10-000-lbs-clear-floor-two-post-lift","title":"Stratus SAE-C10P 10,000 Lbs Clear Floor Two Post Lift","description":"\u003ch2\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eStratus SAE-C10P\u003c\/strong\u003e is a \u003cstrong\u003e10,000 lb\u003c\/strong\u003e two-post car lift built on a clear-floor, overhead design. The equalizer cables and hydraulic lines route through the top beam, so the floor between the columns stays completely open — no base plate to step over when you roll a jack, transmission stand, or creeper under the vehicle. A single power unit drives the carriages directly, and a \u003cstrong\u003esingle-point manual release\u003c\/strong\u003e drops both sides together from one lever.\u003c\/p\u003e\n\u003cp\u003eThe arms set up two ways from the same lift. Run them symmetrically to center the load between the columns for trucks and vans, or asymmetrically to shift the vehicle rearward so the doors clear the posts on cars and daily drivers. The lift raises to \u003cstrong\u003e76 3\/4\" without the adapters\u003c\/strong\u003e and to \u003cstrong\u003e81 7\/8\"–82 11\/16\" with the included truck adapters\u003c\/strong\u003e, and drops as low as \u003cstrong\u003e3 3\/4\"\u003c\/strong\u003e to reach low-profile frames.\u003c\/p\u003e\n\u003cp\u003eEach column carries two top limiter switches that stop the carriages at the top of travel, and every lift is proof-tested dynamically at 115% and statically at 150% of rated capacity. The structure is finished in powder-coated Granite Gray (RAL 7026) with Rein Orange (RAL 2004) arms.\u003c\/p\u003e\n\u003ch3\u003eSymmetric and asymmetric setup\u003c\/h3\u003e\n\u003cp\u003eThe two configurations carry different arm reaches and drive-thru clearances. The symmetrical setup gives a 118 1\/8\" span inside the columns and a 107 1\/4\" drive-thru; the asymmetrical setup rotates the columns to a 115 3\/8\" inside span and a 103 15\/16\" drive-thru while opening up door clearance.\u003c\/p\u003e\n\u003cfigure\u003e\n  \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0771\/5550\/0318\/files\/stratus-sae-c10p-10-000-lbs-clear-floor-two-post-lift-configurations-1.webp?v=1780819703\" alt=\"Symmetrical configuration spec table and dimensioned drawings for the Stratus SAE-C10P two-post lift\"\u003e\n  \u003cfigcaption\u003eSymmetrical setup: specifications and clearances.\u003c\/figcaption\u003e\n\u003c\/figure\u003e\n\u003cfigure\u003e\n  \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0771\/5550\/0318\/files\/stratus-sae-c10p-10-000-lbs-clear-floor-two-post-lift-configurations-2.webp?v=1780819703\" alt=\"Asymmetrical configuration spec table and dimensioned drawings for the Stratus SAE-C10P two-post lift\"\u003e\n  \u003cfigcaption\u003eAsymmetrical setup: specifications and clearances.\u003c\/figcaption\u003e\n\u003c\/figure\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eSymmetric and asymmetric installation from one lift\u003c\/li\u003e\n  \u003cli\u003eOverhead, clear-floor design — open floor between the columns\u003c\/li\u003e\n  \u003cli\u003eDirect drive — no chains or lifting screws in the load path\u003c\/li\u003e\n  \u003cli\u003eSingle-point manual release drops both carriages together\u003c\/li\u003e\n  \u003cli\u003eTwo top limiter switches stop travel at full rise\u003c\/li\u003e\n  \u003cli\u003eProof-tested at 115% of rated capacity (dynamic) and 150% (static)\u003c\/li\u003e\n  \u003cli\u003ePowder-coated finish: Granite Gray (RAL 7026) columns, Rein Orange (RAL 2004) arms\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\u003cth colspan=\"2\"\u003eStratus SAE-C10P Specifications\u003c\/th\u003e\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eCapacity\u003c\/td\u003e\n\u003ctd\u003e10,000 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eConfigurations\u003c\/td\u003e\n\u003ctd\u003eSymmetric and asymmetric\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eDesign\u003c\/td\u003e\n\u003ctd\u003eOverhead, clear-floor\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eDrive\u003c\/td\u003e\n\u003ctd\u003eDirect drive\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eMax lifting height, no adapters\u003c\/td\u003e\n\u003ctd\u003e76 3\/4\" (1,950 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eMax lifting height, with adapters\u003c\/td\u003e\n\u003ctd\u003e81 7\/8\" (2,080 mm) symmetric \/ 82 11\/16\" (2,100 mm) asymmetric\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eMin height, no adapters\u003c\/td\u003e\n\u003ctd\u003e3 3\/4\" (95 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eMin pad height, with adapters\u003c\/td\u003e\n\u003ctd\u003e5 1\/8\" (130 mm) symmetric \/ 3 15\/16\" (100 mm) asymmetric\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eFront arm reach\u003c\/td\u003e\n\u003ctd\u003e33 7\/16\" to 53 1\/8\" (850 to 1,350 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eRear arm reach\u003c\/td\u003e\n\u003ctd\u003e27 9\/16\" to 42 1\/8\" (700 to 1,070 mm) symmetric \/ 23 13\/16\" to 41 3\/4\" (605 to 1,060 mm) asymmetric\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eRise time\u003c\/td\u003e\n\u003ctd\u003e~50 seconds\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eClearance inside columns\u003c\/td\u003e\n\u003ctd\u003e118 1\/8\" (3,000 mm) symmetric \/ 115 3\/8\" (2,930 mm) asymmetric\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eDrive-thru clearance\u003c\/td\u003e\n\u003ctd\u003e107 1\/4\" (2,724 mm) symmetric \/ 103 15\/16\" (2,640 mm) asymmetric\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eOverall height\u003c\/td\u003e\n\u003ctd\u003e151\" (3,835 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eOverall length\u003c\/td\u003e\n\u003ctd\u003e140 3\/16\" (3,560 mm) symmetric \/ 149 5\/8\" (3,800 mm) asymmetric\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eMotor\u003c\/td\u003e\n\u003ctd\u003e3 HP, 220V, 60 Hz, single-phase\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eBreaker\u003c\/td\u003e\n\u003ctd\u003e30A\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eHydraulic oil\u003c\/td\u003e\n\u003ctd\u003eAW32 or AW46\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eShipping weight\u003c\/td\u003e\n\u003ctd\u003e1,539 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eShipping dimensions\u003c\/td\u003e\n\u003ctd\u003e116\" L x 26\" W x 36\" H\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eFinish\u003c\/td\u003e\n\u003ctd\u003ePowder-coated Granite Gray (RAL 7026), Rein Orange (RAL 2004) arms\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\u003ctd colspan=\"2\"\u003e\u003cem\u003eRequires a concrete pad at least 6\" thick at 3,000 PSI, cured a minimum of 28 days. Stratus recommends 6 to 12 inches of reinforced concrete.\u003c\/em\u003e\u003c\/td\u003e\u003c\/tr\u003e\n  \u003ctr\u003e\u003ctd colspan=\"2\"\u003e\u003cem\u003eElectrical: 3 HP single-phase motor on a 30A breaker. A plug is not included; a 220 to 250V, 30A plug is required. Power cord reaches 11 ft.\u003c\/em\u003e\u003c\/td\u003e\u003c\/tr\u003e\n  \u003ctr\u003e\u003ctd colspan=\"2\"\u003e\u003cem\u003eShips with 16 anchor bolts (3\/4\" diameter x 6\" long), torqued to 90 ft-lb (never below 80 or above 110 ft-lb).\u003c\/em\u003e\u003c\/td\u003e\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003e4 screw-up rubber pads, 50 mm (4\") peg\u003c\/li\u003e\n  \u003cli\u003e8 truck adapters — four at 2 3\/4\" and four at 4\"\u003c\/li\u003e\n  \u003cli\u003e16 anchor bolts, 3\/4\" diameter x 6\" long\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cfigure\u003e\n  \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0771\/5550\/0318\/files\/stratus-sae-c10p-10-000-lbs-clear-floor-two-post-lift-truck-adapter.jpg?v=1780819703\" alt=\"Two stacked steel truck adapters and a screw-up rubber pad on a telescoping lift arm\"\u003e\n  \u003cfigcaption\u003eIncluded truck adapters and screw-up rubber pad.\u003c\/figcaption\u003e\n\u003c\/figure\u003e\n\u003cp\u003eOptional accessories, sold separately: cradle pads (50 mm peg) and a tripod jack stand.\u003c\/p\u003e\n\u003ch2\u003eWarranty\u003c\/h2\u003e\n\u003cp\u003eStratus backs the SAE-C10P with a \u003cstrong\u003e5-year warranty on the lifting structure\u003c\/strong\u003e, \u003cstrong\u003e3 years on hydraulic components\u003c\/strong\u003e, and \u003cstrong\u003e2 years on electrical parts\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch2\u003eShipping \u0026amp; delivery\u003c\/h2\u003e\n\u003cp\u003eThe SAE-C10P ships as palletized LTL freight — columns, arms, and hardware arrive crated and strapped on a pallet. Plan for offloading at delivery: a crate at this weight (1,539 lb) typically needs a forklift or a lift-gate truck. Delivery options and any residential or lift-gate surcharges vary by destination, so contact MGS at \u003ca href=\"mailto:sales@mygaragesupplies.com\"\u003esales@mygaragesupplies.com\u003c\/a\u003e or \u003ca href=\"tel:+13073811810\"\u003e307-381-1810\u003c\/a\u003e to confirm freight scheduling before you order.\u003c\/p\u003e\n\u003cfigure\u003e\n  \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0771\/5550\/0318\/files\/stratus-sae-c10p-10-000-lbs-clear-floor-two-post-lift-packaging.jpg?v=1780819703\" alt=\"The lift crated as palletized freight: shrink-wrapped columns and boxed hardware strapped to a pallet\"\u003e\n  \u003cfigcaption\u003eShips as palletized freight.\u003c\/figcaption\u003e\n\u003c\/figure\u003e\n\u003ch2\u003eFAQ\u003c\/h2\u003e\n\u003ch3\u003eWhat concrete does it need?\u003c\/h3\u003e\n\u003cp\u003eA pad at least 6\" thick at 3,000 PSI, cured a minimum of 28 days. Stratus recommends 6 to 12 inches of reinforced concrete.\u003c\/p\u003e\n\u003ch3\u003eWhat are the electrical requirements?\u003c\/h3\u003e\n\u003cp\u003eThe 3 HP motor runs on 220V single-phase power and a 30A breaker. A plug is not included — you supply a 220 to 250V, 30A plug. On the wiring, the yellow\/green lead is ground and the other two are hot. The power cord reaches 11 ft.\u003c\/p\u003e\n\u003ch3\u003eDoes it come with anchor bolts?\u003c\/h3\u003e\n\u003cp\u003eYes — 16 anchor bolts, 3\/4\" diameter and 6\" long. Torque them to 90 ft-lb, never below 80 or above 110 ft-lb.\u003c\/p\u003e\n\u003ch3\u003eCan I change the lifting speed?\u003c\/h3\u003e\n\u003cp\u003eYes. The oil flow valve adjusts it: turn clockwise to slow the lift, counter-clockwise to speed it up.\u003c\/p\u003e\n\u003ch2\u003eDocuments\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0771\/5550\/0318\/files\/stratus-sae-c10p-10-000-lbs-clear-floor-two-post-lift-manual.pdf?v=1780819706\" target=\"_blank\" rel=\"noopener noreferrer\" aria-label=\"Stratus SAE-C10P owner's and installation manual, PDF, opens in new tab\"\u003eOwner's \u0026amp; Installation Manual (PDF)\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0771\/5550\/0318\/files\/stratus-sae-c10p-10-000-lbs-clear-floor-two-post-lift-brochure.pdf?v=1780819705\" target=\"_blank\" rel=\"noopener noreferrer\" aria-label=\"Stratus SAE-C10P product brochure and specification sheet, PDF, opens in new tab\"\u003eProduct Brochure \u0026amp; Spec Sheet (PDF)\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0771\/5550\/0318\/files\/stratus-sae-c10p-10-000-lbs-clear-floor-two-post-lift-faq.pdf?v=1780819702\" target=\"_blank\" rel=\"noopener noreferrer\" aria-label=\"Stratus SAE-C10P frequently asked questions, PDF, opens in new tab\"\u003eFrequently Asked Questions (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Stratus Auto Equipment","offers":[{"title":"Default Title","offer_id":51933893951774,"sku":"SAE-C10P","price":4435.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0771\/5550\/0318\/files\/stratus-sae-c10p-10-000-lbs-clear-floor-two-post-lift-hero.webp?v=1780820574","url":"https:\/\/mygaragesupplies.com\/products\/stratus-sae-c10p-10-000-lbs-clear-floor-two-post-lift","provider":"My Garage Supplies","version":"1.0","type":"link"}